Innocoat Reactafil LS Densifier
Nano Lithium Silicate concrete densifier and hardener with deep penetration.
Innocoat Reactafill penetrates deep into the concrete and reacts quickly with the soluble calcium carbonate compounds to create a breathable protective barrier while at the same time strengthening the floor surface. Being a nano lithium silicate this process is faster with greater coverage than other silicates.
Innocoat Reactafill densifies and hardens the surface wear layer to prevent flaking or peeling, efflorescence is eliminated and surface dusting is prevented. Quick and easy to apply, Innocoat Reactafill is non toxic with no odour, safe to use in food handling areas, has high abrasion resistance and is stain and water resistant.
Innocoat Reactafil can be used on both new and old concrete - however it must be noted that it will not improve the hardness of concrete that is already dusting or disintegrating.
Innocoat KL156 Surface Densifier / Dustproofer
KL156 Surface Densifier is a Potassium / Lithium silicate penetrating densifier used to impregnate and densify concrete, leaving a tough dust free surface
Designed to penetrate the pores and react with the calcium hydroxide in the concrete KL156 Surface Densifer/Dustproofer fuses with the CSH ( calcium silicate hydrate) forming a gel that hardens to densify the concrete. Moisture permeability and efflorescence are reduced leaving the concrete stronger and protected against damage from oils, grease, water and other substrates.
KL156 Surface Densifier/Dustproofer can be used to cure and densify new concrete or to penetrate existing concrete to improve strength and assist with crack prevention. Note it will no improve the hardness of concrete that is already dusting or disintegrating. Innocoat KL156 Surface Densifier / Dustproofer is water based, non toxic, environmentally friendly with no odour and is easy to apply.It works against staining, mould and mildew, oils, water mitgration, concrete dusting, algae & bacteria.
Innocoat Natural Repel
Natural Repel penetrates, cures and seals new or existing concrete.
Ecofriendly Innocoat Natural Repel eliminates dusting and improves abrasion resistance while retaining the natural nonslip surface. Natural Repel's unique colloidal properties bond with the CSH ( calcium silicate hydrate) leaving the concrete stronger and more impervious to wear and staining.
Innocoat Natural Repel is easy to apply, non toxic and can be trafficked on as soon as the surface is dry.
Ideal for any concrete structure, factory floors, garages, driveways, pavers, bench tops, patios, foundations.
Surf Retard Red
For all your exposed aggregate requirements on horizontal surfaces, designed for maximum concrete strength up to 25 MPA.
Easily create that decorative exposed finish with increased anti slip properties. The retarding agents in Surf Retard Red react with the cement in the concrete surface, slowing the set of the surface layer to a depth of 3mm to 8 mm while the concrete below sets, curing to its full strength. This allows the concrete surface (paste) to be removed easily by brushing or with water, leaving an exposed aggregate finish.
Surf Retard Xtra
For all your exposed aggregate requirements on horizontal surfaces, designed for maximum concrete strength over 25 MPA
Easily create that decorative exposed finish with increased anti slip properties. The retarding agents in Surf Retard Red react with the cement in the concrete surface, slowing the set of the surface layer to a depth of 4mm to 10 mm while the concrete below sets, curing to its full strength. This allows the concrete surface (paste) to be removed easily by brushing or with water, leaving an exposed aggregate finish.
Eco Form Release
Eco-Friendly, plant oil based Form Release Concentrate
SyT-Etch
SyT-Etch is an environmentally friendly
SyT-Etch is an environmentally friendly, synthetic acid that replaces the need to use harsh acids commonly used to remove hardened concrete and mortar from concrete forms and other associated equipment. SyT-Etch is safe to use, safe for the environment and 100% biodegradable. Non-corrosive and easy to use, just spray on, brush on or soak for heavier build ups. When used to prepare concrete for sealing no neutralisation step is required, simply rinse off and allow to dry.
SyT-Etch is an environmentally friendly option to using harsh acids for prepping concrete for sealing
SyT-Etch is an environmentally friendly, synthetic acid that replaces the need to use harsh acids commonly used to remove hardened concrete and mortar from concrete forms and other associated equipment. SyT-Etch is safe to use, safe for the environment and 100% biodegradable. Non-corrosive and easy to use, just spray on, brush on or soak for heavier build ups. When used to prepare concrete for sealing no neutralisation step is required, simply rinse off and allow to dry.